High-performance water-based satin acrylic system, designed to adhere to vertical and horizontal tiles in domestic environments (kitchen, bathroom, bedrooms) and in high-traffic public places, it is perfect on stoneware, terracotta and concrete floors..

The REVIVE system consists of the REVIVE water-based enamel to be added with the special REVIVE Active activator and, in the case of application on floors, with REVIVE Antiskid which gives the product anti-slip properties

What is included in the price shown:

1 Jar of REVIVE 750ml or 2.5lt

1 Jar of REVIVE ACTIVE if the 750ml format is purchased and 3 Jars if the 2.5lt format is purchased.

BUY ADD-ONS:

Revive Antiskid

Revive Active

 

Composition:

Single-component, physical drying, semi-gloss, acrylic finishing layer paint in water dispersion. Classified according to UNI 8681:B4. C.O.A.1.FA

 

Main properties:

• fast
• easy
• clean

 

Uses:

The REVIVE system can be applied to various types of surfaces such as walls and floors, both cement and stoneware, terracotta or clinker tiles. It is suitable for use in kitchens, bathrooms, balconies and in public places such as shops, offices, healthcare environments, schools and premises subject to HACCP

 

Method of use:

Environmental and substrate conditions:

 Room temperature min +10C / max +35C U.R. <80%0%

Application method:

Short pile velor roller, brush only for small surfaces and finishing touches

Dilution:

5% with Water

Mixing:

Add a bottle of 31100100 REVIVE Active for each 0.750 liter package and 3 bottles in the case of the 2.5 liter package. Mix thoroughly and leave to act for 10 minutes, then proceed with any dilution or application.

 

Theoretical yield:

8-12 m²/l per coat, depending on the absorption of the substrate.

 

APPLICATION CYCLE:

Preparation of the REVIVE system

Add a bottle of REVIVE Active for each 0.750 liter package of REVIVE and 3 bottles in the case of the 2.5 liter package.

Mix thoroughly and, after about 10 minutes, proceed with the possible dilution.

The adhesion promoter will be effective for no more than 3 days, after which it will simply be necessary to restore the addition.

To give an anti-slip effect, the last layer must be added with REVIVE Antiskid to be added in the amount of one bottle for each 0.750 liter package and 3 bottles in the case of the 2.5 liter package.

 

Preparation of the support

Make sure that the residual humidity of the substrate does not exceed 5% in order to avoid possible detachments.

Also check that the substrate temperature is not lower than 10C..

Cement: Make sure that the substrate has matured for at least 1 month and that it is completely dry and free from dirt, dust and loose parts.

Depending on the degree of absorption of the substrate, apply one or more coats of consolidating insulator 23400003 TITANCRIL diluted 1:3 with water, mix very well and distribute the product evenly.

Wait at least 6 hours and apply REVIVE.

Floor tiles:

The surface must be perfectly degreased, free of detergent residues and dry. To avoid water stagnation, external floors must have a minimum slope of 15mm for each meter as prescribed by the UNI 11146 standard, which deals with the criteria for the design, construction and testing of concrete floors.”.

The application system and the preparation of the supports must be evaluated and chosen according to the current state and the conditions to which the support itself will be exposed.

Supports:

The substrates must be sound, clean (without oil and grease), dry and free from salt efflorescence, mould, algae or fungi.

To clean surfaces contaminated by microorganisms, use Biosistem Titansan.

They must not be chalky or have detached parts.

Preparation of the substrates: Sand the surfaces to improve adhesion, clean the substrates and consolidate the crumbling ones.

Repair surface defects by applying suitable professional building products.

Do not apply the product on new plaster for at least 4 weeks.

 

Application methods:

 New cement screed floors:

Apply one or more coats of consolidating insulator 23400003 TITANCRIL diluted 1:3 with water;

Finally, apply two coats of the REVIVE system diluted 5-10% by volume with water, with a short-haired roller, with an interval of 4-6 hours between coats.

 

Deteriorated and irregular cement screed floors, or outdoors:

Degreasing and cleaning of the substrate; removal of inconsistencies and parts in the detachment phase of the old finishing cycle with a floor machine;

Remove any oil and grease by shot peening or removing the affected part of the support; restore any removed parts with special anti-shrinkage fibre-reinforced cement mortars;

Apply one or more coats of consolidating insulator 23400003 TITANCRIL diluted 1:3 with water;

Finally, apply two coats of the REVIVE system diluted 5-10% by volume with water with a short-haired roller, with an interval of 4-6 hours between coats.

Tiled floors:

Check that the tiles are perfectly anchored to the substrate, if not, remove them and replace with similar tiles and wait for the adhesives/grouts to dry; Degrease and wash the floor;;

Carry out a preventive sampling to verify perfect adhesion to the support;

Apply, with a short-haired roller, two coats of REVIVE system diluted 5-10% by volume with water, with an interval of 4-6 hours between coats.

Floors already treated and/or painted with specific products:

Degreasing and cleaning of the substrate; removal of inconsistencies and parts in the detachment phase of the old finishing cycle with a floor machine; remove any oil and grease by shot peening or removing the affected part of the support; restore any parts removed with special anti-shrinkage fibre-reinforced cement mortars

Carry out a preventive sampling to verify perfect adhesion to the substrate

Apply a preliminary coat of REVIVE system diluted 2:1 with water;

Apply, with a short-haired roller, two coats of REVIVE system diluted 5-10% by volume with water, with an interval of 4-6 hours between coats.

Shaved or civil plastered or concrete walls:

Apply one or more coats of consolidating insulator 23400003 TITANCRIL diluted 1:3 with water;

Finally, apply two coats of the REVIVE system diluted 5-10% by volume with water, with a short-haired roller, with an interval of 4-6 hours between coats.

Walls already painted with well anchored washable paints:

Apply a preliminary coat of REVIVE system diluted 2:1 with water;

Finally, apply two coats of the REVIVE system diluted 5-10% by volume with water, with a short-haired roller, with an interval of 4-6 hours between coats.

Irregular plasters, plasterboard and gypsum smoothing:

Level the surfaces smoothing them with TITANSTUCCO, wait for total drying and sand to eliminate smudges and excess grout;

Apply one or more coats of consolidating insulator 23400003 TITANCRIL diluted 1:3 with water

Finally, apply two coats of the REVIVE system diluted 5-10% by volume with water with a short-haired roller, with an interval of 4-6 hours between coats.

Tiled walls:

Check that the tiles are perfectly anchored to the substrate, if not, remove them and replace with similar tiles and wait for the adhesives/grouts to dry;

Degrease, sand the substrates and brush;

Carry out a preventive sampling to verify perfect adhesion to the support;

Apply, with a short-haired roller, two coats of REVIVE system diluted 5-10% by volume with water, with an interval of 4-6 hours between coats.

IMPORTANT NOTES:

Do not apply REVIVE on surfaces with standing water, nor on shower trays or bathtubs.

REVIVE can only be tinted with the coloring pastes of the Colormaker Tintometric Systems.

REVIVE can be walked on with caution 6-8 hours after application and reaches maximum resistance after about 15 days. During this time, do not cover the substrate with cardboard, sheeting, etc. if not temporarily, to allow it to dry properly.

Due to the various types of existing flooring, we suggest carrying out a preventive test on a test area before proceeding with the total painting of the premises.

The presence of any waxes, silicones, greases or in any case unsuitable substrates can compromise the adhesion of the product.

For outdoor use, avoid application in anticipation of high atmospheric humidity (see formation of frost or dew) or in anticipation of rain for the first 6/7 days after application as these could hinder the correct filming of REVIVE.

One week after application, the applied product must be sanded if it becomes necessary to apply another coat and/or make touch-ups.

 Do not clean with alcohol-based cleaners.

 

WARNINGS:

Wash brushes and tools with water immediately after use, do not disperse the washing water into the soil or surface waters. Keep out of reach of children. For more information, consult the Safety Data Sheet.

 

 

Disposal:

REVIVE Jar: C/PP91 - Plastic Collection

REVIVE cap: FE40 - Ferro Collection.

REVIVE ANTISKID jar: PP05 Plastic collectiona

REVIVE ACTIVE Jar: PP05 Plastic Collectiona

Recycle only if perfectly clean and empty.

Otherwise recycle on special ecological centers.

REVIVE Hazard Label:

Indications of danger:

EUH210 Safety data sheet available on request.

EUH208 Contains: MIXTURE OF:5-CHLORO-2_METHYL-2H-ISOTHIAZOL-3-ONE [EC no.247-500-7];

2-METHYL-2H-ISOTHIAZOL-3-ONE [EC no. 220-239-6] (3:1)

1,2- BENZISOTHIAZOL- 3(2H)-ONE

May cause an allergic reaction