Your subheading
Your title
MAFRA Maniac Foam Gun Prewash Prelavaggoo foaming MF88 MF114 1-5LT
Format:
Format
Quantity:
Pickup available at Punto Vendita Net Coatings
Usually ready in 1 hour
MAFRA Maniac Foam Gun Prewash Prelavaggoo foaming MF88 MF114 1-5LT
1LT MF88
Punto Vendita Net Coatings
Pickup available, usually ready in 1 hour
Via Emilia 2
35043 Monselice PD
Italy
Subheading
Multi-column
Your content
Your content
Your content
Your content
Your subheading
Your title
Your subheading
Your title
Your subheading
Your title
Foam Gun Prewash of the Maniac Line™ by Mafra is one powerful and safe foaming agent dry and compact foam for foam gun to be used in the pre-wash phase. Respects previously applied protectants, including nanotechnology-based protectants or coatings.
This product, when used in combination with a pressure washer, allows you to remove 90% of dirt allowing to prevent swirl or micro-scratches in subsequent washing stages
HOW TO USE:
It is recommended for use with a foam gun but can also be used as an excellent pre-wash with a low-pressure manual pump:
With Foam Gun:
In winter dilute 1:5 (1 part product to 5 parts water) to achieve a final dilution of 1:50 on output;
In summer dilute 1:10 (1 part product to 10 parts water) to achieve a final dilution of about 1:110 on output;
Apply a thick layer of foam onto the vehicle;
Let the product act on the surface and wait for the foam to start falling off (this may take up to 5 minutes);
Rinse the vehicle from top to bottom.
With Low-Pressure Manual Pump:
In winter dilute 1:50 (1 part product to 50 parts water) – 2 caps in 1 liter of water;
In summer dilute 1:100 (1 part product to 100 parts water) – 1 cap in 1 liter of water;
Apply the product onto the vehicle;
Let the product act on the surface for one minute without letting it dry on the bodywork;
Rinse the vehicle from top to bottom.
RECOMMENDATIONS:
Make sure the vehicle surface is cold and the car is in the shade, avoiding direct sunlight.
Before using the product in summer, rinse the vehicle to cool the surface or to remove the initial layer of dirt.
The product should be applied from bottom to top. During hot seasons, work on one panel at a time to prevent the product from drying on the surface.
It is possible to apply the product directly onto the bodywork without wetting it first, even in the presence of stubborn dirt such as insects and the lower parts of the car, which are always the dirtiest.
If there is mud, remove it with a water jet before applying the product.
It is recommended for use with a foam gun but can also be used as an excellent pre-wash with a low-pressure manual pump:
With Foam Gun:
In winter dilute 1:5 (1 part product to 5 parts water) to achieve a final dilution of 1:50 on output;
In summer dilute 1:10 (1 part product to 10 parts water) to achieve a final dilution of about 1:110 on output;
Apply a thick layer of foam onto the vehicle;
Let the product act on the surface and wait for the foam to start falling off (this may take up to 5 minutes);
Rinse the vehicle from top to bottom.
With Low-Pressure Manual Pump:
In winter dilute 1:50 (1 part product to 50 parts water) – 2 caps in 1 liter of water;
In summer dilute 1:100 (1 part product to 100 parts water) – 1 cap in 1 liter of water;
Apply the product onto the vehicle;
Let the product act on the surface for one minute without letting it dry on the bodywork;
Rinse the vehicle from top to bottom.
RECOMMENDATIONS:
Make sure the vehicle surface is cold and the car is in the shade, avoiding direct sunlight.
Before using the product in summer, rinse the vehicle to cool the surface or to remove the initial layer of dirt.
The product should be applied from bottom to top. During hot seasons, work on one panel at a time to prevent the product from drying on the surface.
It is possible to apply the product directly onto the bodywork without wetting it first, even in the presence of stubborn dirt such as insects and the lower parts of the car, which are always the dirtiest.
If there is mud, remove it with a water jet before applying the product.
