SIKA
SikaForce 301 Two-Component Adhesive for Repairing Purform Plastics Fast 3.5 minutes 736294
SikaForce 301 Two-Component Adhesive for Repairing Purform Plastics Fast 3.5 minutes 736294
Punto Vendita Net Coatings
Via Emilia 2
35043 Monselice PD
Italy
SikaForce 301 Purform based fast curing plastic repair adhesive®
EX SIKA CODE: 2920 - 2950
SikaForce-301 (Purform) is based on Purform, an industry-leading polyurethane with less than 0.1% monomeric diisocyanate for improved occupational health and safety protection. SikaForce-301 (Purform) is specifically designed for repairing plastic parts in automotive workshops.iche.
It provides good adhesion to various types of plastic and can be overpainted with almost all types of paint.
Less than 0.1% monomeric diisocyanate for better occupational health and safety protection
Good adhesion on a wide variety of substrates
Rapid polymerization at room temperature
ADVANTAGES
- Less than 0.1% monomeric diisocyanate for better occupational health and safety protection
- Good adhesion on a wide variety of substrates
- Rapid polymerization at room temperature
- Sandable after just 30 minutes
- Overpaintable
- No slipping or dripping
- No volumetric shrinkage
Jobs
SikaForce-301 (Purform) is used in automotive workshops for plastic repair work such as damage to bumpers, bonding of plastic parts and brackets, recreating plastic clips or filling unused sensor openings and small holes. This product is only suitable for experienced professional users. Testing with real-world substrates and conditions must be performed to ensure material adhesion and compatibility.i.
DANGER LABEL:
H319 Causes serious eye irritation
Prevention: P264 Wash skin thoroughly after use. P280 Wear eye protection/face protection. Reaction: P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove any contact lenses if it is easy to do so. Continue rinsing. P337 + P313 If eye irritation persists, get medical advice/attention.
COMP. B:
H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H332 Harmful if inhaled. H335 May cause respiratory irritation
P261 Avoid breathing mist or vapours. P280 Wear gloves/eye protection/face protection. Reaction: P304 + P340 + P312 IF INHALED: remove the victim to fresh air and keep him at rest in a position comfortable for breathing. If you feel unwell, call a POISON CENTER/doctor. P333 + P313 If skin irritation or rash occurs: Get medical advice/attention. P337 + P313 If eye irritation persists, get medical advice/attention. P362 + P364 Take off all contaminated clothing and wash it before reuse.
Thoroughly clean and degrease the entire bonding surfaces with Sika® Cleaner G+P and a clean cloth. Then sand the surfaces with sandpaper grit 80 - 180.
Clean the entire bonding surface again with Sika® Cleaner G+P and a clean cloth. Ensure the surface is completely dry and free of moisture before proceeding to the next step of the process.
Spray a thin layer of SikaForce®-300 Primer on both sides and let it dry for at least 5 minutes. Further surface treatments depend on the specific nature of the substrates.
Application:
SikaForce®-301 (Purform®) should be processed between 15 °C and 30 °C (product, environment, and substrate temperature).
Extrude the adhesive without a mixer to level the levels. Attach the static mixer, dispense one-third of the mixer length and discard it before starting to apply the adhesive to the bonding area.
Dispense SikaForce®-301 (Purform®) with suitable piston guns. Mixer Tips for SikaForce®-301 are required for proper mixing (part of the package and sold separately).
After dispensing, leave the mixer on the cartridge until the adhesive is reused. The remaining adhesive will last for several weeks if stored correctly.
To reuse SikaForce®-301 (Purform®), remove the static mixer and dispose of it properly. Clean the cartridge outlet thoroughly. Then connect a new mixer and start dispensing as described above.
Sika Contouring Film and Reinforcement Mesh are available for remodeling and modeling activities.
Removal:
Uncured SikaForce®-301 (Purform®) can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically.
Hands and exposed skin should be washed immediately using hand wipes like Sika® Cleaner-350H or a suitable industrial hand cleaner and water.
Do not use solvents on the skin.
STORAGE CONDITIONS:
Uncured SikaForce®-301 (Purform®) should be stored between 15 °C and 30 °C in a dry place. Do not expose it to direct sunlight or frost.