Megasid Aluminum Base Stucco for Aluminum Repairs 1kg + CATALYST

The two-component putty MEGASID ALUMINUM PASTA is a formulation based on unsaturated polyester resins and aluminum paste; it is an extremely tenacious and resistant product, while retaining good characteristics of spreadability and sandability.

It is mainly used on aluminum bodies and for the reconstruction of missing body parts. Thanks to its innovative formulation it is suitable for being drilled and threaded and can also be used successfully to replace some welds.

TECHNICAL DATA:

 

Specific weight	1460 20g/mll		(MI 001)
V.O.C.	41 2 g/ll		(ASTM 2369)
Viscosity	3000 300 Passs		(MI 002B; 25C))
Consistency	2200 200 Passs		(MI 002B; 25C))
Color		Aluminum

 

APPLICATION:

• Make sure that the surfaces to be grouted are perfectly dry and clean, in case of application on bare sheet metal, sand it with P 80 and P 150 abrasive papers;
• Take the quantity to use from the jar with clean tools, adding 1 - 3 grams of hardener for every 100 grams of product; Mix this quantity by amalgamating the two components well;;
• Apply the filler on the surface to be worked on, bearing in mind that the product can be sanded (dry P 80 P 120 grit) after about 30 - 40 minutes; the hardening times can be altered according to the ambient temperature: they shorten with temperatures above 25 C and lengthen with lower temperatures;i;
• Do not put catalysed and/or unused grout back into the can to prevent the entire contents of the can from deteriorating;
• Close the jar after use, in order to prevent the product from hardening in contact with air.

APPLICATION: SPATULA

CATALYSIS: 1-3%

DRYING:

GEL TIME: 6-8 minutes

OUT OF FOOTPRINT: 10-30 minutes

COMPLETE DRYING: <1 hour

SANDABLE: After 30-40 minutes

 

Disposal:

Jar: FE40 - Iron Collection

Cap: HDPE2 - Plastic collection.

Recycle only if perfectly clean and empty.

Otherwise recycle on special ecological centers.

Hazard label:

UFI: FGA0-P0N9-900W-CNJ4

 

H226Flammable liquid and vapour.

H361dSuspected of damaging the unborn child.

H372Causes damage to organs through prolonged or repeated exposure.

H319Causes serious eye irritation.

H315Causes skin irritation.

H335May cause respiratory irritation.

H317May cause an allergic skin reaction.

H412Harmful to aquatic life with long lasting effects.

P201 Obtain special instructions before use.

P210Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Not smoking.

P260Do not breathe dust / fume / gas / mist / vapors / spray.

P280Wear protective gloves and eye/face protection.

P308+P313IF exposed or concerned, get medical advice/attention.

P370+P378 In case of fire: Use carbon dioxide, foam, chemical powder to extinguish.

Contains: STYRENE ANHYDRIDE MALEICANAPHTA SOLVENT (PETROLEUM), LIGHT AROMA

VOC expressed in g/litre of ready-to-use product: 41.00

Maximum limit : 250.00

UFI CATALYST: V800-F0JP-U00J-NPDK

Instructions for use

Make sure that the surfaces to be filled are perfectly dry and clean; if applying to bare metal, sand it with abrasive paper P 80 and P 150;
Take the amount to use from the jar with clean tools, adding 1 - 3 grams of hardener for every 100 grams of product;
Mix this amount well, combining the two components;
Apply the filler to the surface to be worked on, keeping in mind that the product can be sanded (grit P 80 – P 120 dry) after about 30 - 40 minutes; the curing times may vary depending on the ambient temperature: they shorten with temperatures above 25 °C and lengthen with lower temperatures;
Do not return catalyzed and/or unused filler to the jar to avoid deteriorating the entire contents of the jar;

Close the jar after use to prevent the product from hardening upon contact with air.

APPLICATION: SPATULA
CATALYSIS: 1-3%
DRYING:
GEL TIME: 6-8 minutes
OUT OF PRINT: 10-30 minutes
COMPLETE DRYING: <1 hour
SANDABLE: After 30-40 minutes

Disposal:

Jar: FE40 - Iron Collection
Cap: HDPE2 - Plastic Collection.

Recycle only if perfectly clean and empty.
Otherwise, recycle at appropriate ecological centers.